Spinning equipment must be correctly selected for solving certain tasks. In this guide, we will consider the nuances of the correct winding of the fishing line. This will help avoid unpleasant factors on fishing and frustration. You will also find step-by-step instructions on how to wind the fishing line on the inertia-free reel, diagrams of the attachment of the fishing line to the spool and reel settings. There are no special secrets here.
How to wind the line on the inertia reel?
It would seem that everything is very simple, even in the instructions for the inertia-free coil a simple scheme is indicated, take it and wind the line. But with this attitude, the very first fishing can end in unpleasant moments in the form of disentangling the "beard" and self-resetting loops instead of fishing. In order to prevent this, we have prepared a material on how to wind the fishing line on the inertia-free reel. It is not as difficult as it may seem. We will also look at how to use a non-spinning reel.
Options for winding fishing line and the choice of inertia reel
As a rule, beginners in spinning fishing begin with small light rods and corresponding reels. Most often, this is an inertialess coil with a size of 1500-2500, which can hold 100 meters of fishing line with a section of 0.25-0.30 mm. In addition to size, they differ in the type of winding fishing line. So, reverse conical, straight conical or cylindrical straight winding is possible. If you have an inexpensive Chinese inertia-free reel, then you need to be prepared for random and chaotic styling. And if this winding is not critical for ordinary fishing line, then it is undesirable to use a cord on such a coil. After all, even the correct prefilling of the cord with the backing will not protect against further “beards” or bad casts due to entanglement and overlap of tight braids.
If we consider a quality forest laying machine, then a coiled fishing line in profile should create a straight line. Parallel spool, straight during cylindrical winding and oblique - during the cone. In certain models of coils, for example “Shimano”, you can change the winding profile of a fishing line by installing a washer under the spool. In some mechanisms, in which the winding profile is determined by the taper of the spool, it can be changed by winding the backing under the main line.
How to reel on a spinning fishing line?
At first, put a reel on some static pin (needle, screwdriver, pencil). You can ask someone to hold the design. Reel should rotate easily. After the line is passed through all the rings of the spinning, and at its end a knot is made. Refueling begins with mounting on the spool. Lift the shackle of the forest laying machine, wrap the fishing line over the spool, tie another Arbor knot and tighten it, then lower the laying forest.
If you wound the cord, then under the place of fastening glue the plasters, and even here it is better to put a piece of gum with a fingertip. So you will avoid slipping from the spool of fishing line. Then start to wind it, rotating evenly the handle of the coil. We must not forget that during the refuelling line must be in the tense position. Tension is achieved by holding the bobbin. To prevent cuts, do not hold the fishing line with bare hands, use a piece of dense material or a glove.
As a backing, a fishing line with a cross section of up to 0.30 mm is used. The use of large cross-section material can lead to further uneven winding of the main line. Also it is necessary to choose a backing from a kapron or cotton thread, they dry up for a long time if wetted while fishing.
As for the volume of the line for backing, it can only be determined empirically. For this we will need a second removable spool. Directly, the process looks like this: first, the main fishing line is wound onto the spare spool, after - backing, indented several millimeters from the side. Then the main spool is attached to the reel, and the inverse rewinding procedure is done: first, the backing, and then the main fishing line. If there is no spare wheel, then it will be necessary to rewind the entire line twice to a reel or any other reel.
Knot of fastening of a scaffold
It is necessary to fill the spool in such a way that its side does not reach about 2 mm. With this winding, the friction of the fishing line on the rim decreases, it will come out freely during the casting, without creating loops and knots. If the spool is quite deep, and for fishing you need such a volume of thin fishing line, which it is possible to fill the spool with only half or a third, you need to wind the old one under the main fishing line. For this purpose, the material used is thinner than the main one, so that in the end “hillocks” and “dips” are not formed. Very fast winding of the fishing line will lead to the appearance of a "beard" during casting.
No need to fill the spool with a heavier line than that on which the design is calculated. This will greatly affect the outcome. The fishing line will begin to fall and will be confused. During winding on the reel set multiplier sideways relative to the spool. Design fill, not reaching a few millimeters to the edges. Some multipliers are better show themselves when more than filled the spool, but this might only be determined during operation of a coil or to ask about protank coil replacement. Experienced fishermen will gladly tell you how best to do it. Can help sales.
Storage of fishing line on the spool
In the question of how to wind the line on the inertia-free spool, you need to clarify one more thing. It concerns the care of materials. During long-term storage, poorly dried fishing line will lose elasticity. So, it can break at a very important moment. To prevent this, before removing the tackle for a long time, for example, in the off-season, carefully wipe the main line on the floor and let it dry. After it is necessary to return again to the spool. This operation is desirable to do after any fishing. In this case, a piece of exhausting fishing line can be limited to a size slightly larger than it was at a long cast.